BS-922 Quick Guide
Terminal Navigation and Control
: Navigate up and down. F1-F8 : Function buttons.
Enroll an Administrator
Enrolling an administrator means this person will have full access to the device's menu. NOTE: Once a terminal administrator has been enrolled, only device admins will be able to access the device menu.
3. Enter the employee's unique ID (example '888').
Enroll Employee's Fingerprint6. Select Enroll FP by pressing the down button then press the M/Ok button.
7. Select the first finger you like to use and place and remove it three times as prompted by time clock.
8. Press Ok when you are ready to continue with the second finger.
Note: You may enroll up to 5 fingers per employee. Press the ESC button once to finish fingerprint enrollment and returned to previous screen.
Employee's PIN Code (optional)
1. Press and hold the M/Ok button for few seconds. If an admin has been enrolled the time clock will display Admin affirm along with padlock picture. Have the admin place their finger on the sensor.
2. Select User Mng then press the M/OK button.3. Enter the employee's unique ID (example '888').
Enroll Employee's Fingerprint
7. Select the first finger you like to use and place and remove it three times as prompted by time clock.
8. Press Ok when you are ready to continue with the second finger.
Note: You may enroll up to 5 fingers per employee. Press the ESC button once to finish fingerprint enrollment and returned to previous screen.
Employee's PIN Code (optional)
9. Select Enroll PWD press the M/OK button then specify PIN number twice. Select OK on the screen and press the M/OK button.
Security level Assignment
11. Select Purview and use the right arrow to change it to Admin.
Enroll Employee's Proximity Card / FOB (Optional)
10. Select Enroll Card press the M/Ok button. Wave the proximity card / FOB in front of the device keypad.
10. Select Enroll Card press the M/Ok button. Wave the proximity card / FOB in front of the device keypad.
Security level Assignment
11. Select Purview and use the right arrow to change it to Admin.
12. Select OK on the screen then press the M/Ok button to save your employee enrollment.
Enroll an Employee
The process of enrolling am employee is exactly the same as enrolling administrator, however regular employees will not have access to the time clock menu.
1. Press and hold the M/Ok button for few seconds. If an admin has been enrolled the time clock will display Admin affirm along with padlock picture. Have the admin place their finger on the sensor.
2. Select User Mng then press the M/OK button.3. Enter the employee's unique ID (example '888').
Enroll Employee's Fingerprint
7. Select the first finger you like to use and place and remove it three times as prompted by time clock.
8. Press Ok when you are ready to continue with the second finger.
Note: You may enroll up to 5 fingers per employee. Press the ESC button once to finish fingerprint enrollment and returned to previous screen.
Employee's PIN Code (optional)
9. Select Enroll PWD press the M/OK button then specify PIN number twice. Select OK on the screen and press the M/OK button.
Security level Assignment
11. Make sure Purview level is set to User for regular employees
Enroll Employee's Proximity Card / FOB (Optional)
10. Select Enroll Card press the M/Ok button. Wave the proximity card / FOB in front of the device keypad.
10. Select Enroll Card press the M/Ok button. Wave the proximity card / FOB in front of the device keypad.
Security level Assignment
11. Make sure Purview level is set to User for regular employees
12. Select OK on the screen then press the M/Ok button to save your employee enrollment.
Configure Ethernet Communication
1. Press and hold M/OK button for few seconds, then the time clock may display Admin Affirm. The admin must place their finger to access the menu.
2. Select Comm and press the M/OK Button. Select Network and press the M/OK button.3. Specify the IP address, Subnet mask and Gateway.*
*Please consult with your IT department for these information.
*Please consult with your IT department for these information.
4. Select OK on the screen then press the M/Ok button.
Then you will add the device with the IP address into the desktop software.
Configure Wifi Communication
1. Press and hold M/OK button for few seconds, then the time clock may display Admin Affirm. The admin must place their finger to access the menu.
2. Select Comm and press the M/OK Button. Select Wireless LAN and press the M/OK button.
3. Select the network you want to connect to and press M/Ok.
4. Enter the password (press the right arrow on the device to enable letters on the keybaord).
5. Specify the IP address, Subnet Mask and Gateway.* OR select DHCP under IP Address (this will automatically try to get network settings)
*Please consult with your IT department for these information.
*Please consult with your IT department for these information.
6. Select OK on the screen then press the M/Ok button.
7. Press the ESC button several time to get out of the menu.
8. If you used DHCP, after waiting a minute, go back into the menu, then go to Comm and Wifi Setup. Write down the IP address there to add into the software.
Then you will add the device with the IP address into the desktop software.